50 caliber Browning machine gun's top cover). Since it's a two piece unit, the hatch also permits placing the belt by hand into the proper position for firing, just like a standard belt fed machine gun's top cover (in fact, the hinged locking latch on the hatch was taken directly from the American's. To alleviate the situation we have installed a hinged hatch on the feeder/delinker housing for easier access. This was a major project that took at least 20 minutes. As the feeder/delinker components were encased in a solid outer housing, only by removing the feeder/delinker system from the gun and disassembling it, using a pry bar to force the gears around, could clear the stoppage. Whenever a belt restriction occurred (a rather common event) the belt would slew sideways while entering the delinker and one of the stripper teeth would literally pierce the cartridge case, resulting in massive stoppage. The feeder/delinker represented the single greatest problem in the original design. We have recently manufactured a new rotor which holds it's tolerances much closer than encountered on the original version. This allowed the bolt head to wander off-center, resulting in off-center firing pin strikes. As the bolt head moves forward into battery, just prior to rotation it looses all alignment guidance, which was provided by machined lobes on the rotor. Off-center firing pin strikes were also a major problem in the beginning. We now use a 5/16 inch bolt screwed into a castellated nut, locked in place by a cotter pin. This nut all too frequently wore so badly that the clamp was shot off the gun. Originally a 1/4 inch steel bolt was threaded to a self-locking nut. This clamp is held in place by a single bolt. All of the barrels are prevented from rotating out of their retained positions by a barrel clamp which mates with four flanges on the front of each barrel. The six barrels are held to the front of the rotor by an integral interrupted flange on one side of each barrel that requires a 180-degree turn for retention. Original Design Problems and Construction All six bolts repeat this identical process in sequence. Pins in the bolt head interface with the cam surfaces on the firing pin and cause the striker to rotate with the head.Īfter the extraction and the ejection, the bolt has completed a 360-degree cycle and is positioned to pick up another round. A roller on top of the bolt subassembly, moving in an elliptical cam path in the receiver housing, drives the bolt forward.Ī flat dwell profile in the cam path holds the bolt locked briefly until the bullet has traveled past the muzzle and the pressure has dropped to a safe level. The bolt head itself locks into recesses in the rotor (the main structural component of the gun) while the barrel interfaces with the front of the rotor. Rotation into the battery is clockwise with the bolt rotating around the firing pin holding entire bolt assembly together. The bolt subassembly features a helical tang on the bolt head which mates with a helical groove on bolt body. The breech mechanism features a rotating bolt head with two locking surfaces (similar to MG34 GPMG). The barrels rotate counter clockwise and fire in turn when they reach the 12' o-clock position. Operational Specifics: The GP-VG MK2 Venom Gun is electrically operated and utilizes a locking-breech system with six barrels and six bolts. Operation: Electrically operated, locked breech system with six barrels and bolts rotating bolt heads with dual locking surfaces.įeed Mechanism: Gear driven feeder/delinker with two-piece hinged hatch with standard GPMG disintegrating links. M134?Ĭaliber: 7.92 mm (Saboted light armor piercing rounds required for proper feed) This is the intel "Venom tech manual." Any idea what real weapon they stole this writeup from? It's much to detailled to not be real, and I imagine they just copied it out of a textbook for the most part. MattyDienhoff 19:28, 14 February 2011 (UTC) Venom project book intel I've heard of it before and it's my impression that it was quite well known in its day. Can I create a page for it? (It features almost the same weapons as this and some "new", like the BAR, STG-44, M1 Garand. Wolfenstein: Enemy Territory is a free multiplayer game created by the studio Splash Damage which later made Quake: Enemy Territory and Brink.
0 Comments
Leave a Reply. |